This tutorial was written by me on August 23rd, 2013 and is my own creation. Any resemblance to any other tutorial is purely coincidental and unintentional.

PSP Version used: PSP X5, but should work in other versions.

This tutorial assumes you have a good working knowledge of PSP.

Supplies:

Tube of choice. I am using the beautiful work of VeryMany. You can purchase this tube here. 

PTU kit, Sweet Steampunk, by Inzpired Creationz. You can purchase this kit here. 

Mask 1 by me. You can find it here. 

Font of choice. I am using Ventography.

--------------------

Open a blank transparent image, 600 x 600.

Open paper 17 and your mask. Copy and paste your paper as a new layer onto your blank canvas. Apply your mask, merge group. Duplicate once and then merge these two mask layers together.

Open Frame 4. Resize by 67%. Copy and paste as a new layer. Rotate 90 degrees clockwise. Now take your pick/raster deform tool and rotate slightly to the left so it is at an angle.

With your magic wand tool, click inside the frame. Selections, modify, expand by 5.

Open paper 13. Copy and paste as a new layer. Selections, invert, & press delete. Deselect.

Open Frame 3. Resize by 50%. Copy and paste as a new layer. Place to the top right of the square frame. Move this frame below the square frame & paper layer. See below for placement.

With your magic wand, click inside the smaller frame. Selections, modify, expand by 5. Open paper 3. Copy and paste as a new layer. Selections, invert, and press delete. Deselect and move this layer below the circle frame.

Open your tube and resize as necessary. Copy and paste as a new layer above the circle paper layer. Flip tube horizontally and place over the paper. Erase any part of the tube that shows outside the circle frame.

Duplicate your tube, gaussian blur 3.00, blend mode Screen. On the original tube layer, opacity 45.

Copy and paste your tube again, just above the square paper layer. Place to your liking. Erase any part that extends past the square frame. Duplicate your tube, gaussian blur same settings as before. Blend mode Screen, opacity 55. On the original tube layer, opacity 45.

Open Bling 1. Resize by 60%. Copy and paste as a new layer just below the square frame layer. Duplicate and arrange the two copies to your liking.

Open Ribbon 1. Resize by 81%. Copy and paste as a new layer above the square frame layer.

Open the Feathers. Resize by 81%. Copy and paste as a new layer.

Open the Books. Resize by 40%. Copy and paste as a new layer. Place over the loop of the ribbon.

Open Clock 2. Resize by 40%. Copy and paste as a new layer. Place to the bottom left, below the books.

Open the Umbrela. Resize by 60%. Copy and paste as a new layer. Rotate slightly to the right and place to the bottom of the circle frame.

Open your tube again. Copy and paste as a new layer, resize as necessary. Place slightly to the right.

Open the Cog and Wings. Resize by 50%, flip horizontal. Copy and paste as a new layer. Place to the bottom.

Open the Feather. Resize by 50%. Copy and paste as a new layer. Pick tool/raster deform and rotate till it lays flat. Place to the bottom right. Duplicate, flip horizontal. Place to the upper left of the square frame. Now move the duplicate feather below the umbrella layer.

Open Bow 2. Resize by 40%, flip horizontal. Copy and paste as a new layer above the original feather layer. Place to the bottom of the clock.

Open the Boot. Resize by 40%, flip horizontal. Copy and paste as a new layer. Place to the bottom right.

Open Roses 2. Resize by 50%. Copy and paste as a new layer. Place over the bottom feather, allowing some of the feather to show. Duplicate the roses, flip vertical. Place to the top left of the square frame, allowing some of the feather at the top to show through. Now move the duplicate roses layer down just below the umbrella layer.

Open the Antiseptic. Resize by 40%. Copy and paste as a new layer above the original roses layer. Place to the bottom left.

Open Butterfly 3. Resize by 40%. Copy and paste as a new layer. Use your pick/raster deform tool to rotate slightly to the left. Place to the top of the books.

Open Sparkles 1. Resize by 82%. Copy and paste as a new layer.

Open Sparkles 2. Resize by 80%. Copy and paste as a new layer.

Add your name, copyrights, license info. Apply a drop shadow of choice, merge visible. Save as a PNG.

Thanks for checking out my tutorials.